TECHNICAL CHARACTERISTICS
LCD Graphic Display 192x64 pixel, 95X45 mm With backlight
With built-in LED :
- Test-Aut-Man-Reset-Help-Mains Contactor & Generator Contactor
Key only
6 PROGRAMMING KEYS
- Enter-Exit-Scroll Parameters ▲▼-Increase and Decrease Parameters
INDICATOR LEDS
- Engine running
- Generator powered
- Mains powered
- Mains contactor closed
- Generator contactor closed
- Help message
- Test key pressed
- Automatic key pressed
- Manual key pressed
- Reset key pressed
|
Large size graphical Display
By displying at the same time of 8 typical values and
character dimension of 10mm
sample: 3 voltages- 3 currents- frequency kVA
Note “Mains” or “Generator” appears on the display to
point out to which unit the aspects displayed refer to:
- Battery voltage
- Mains and phase generator voltages, between the
lines of the system
- Phase currents
-
Phase and total active, reactive and apparent powers
- Active, reactive and apparent energy
- P.F.- Power factor of each phase
- Energy meter
- Frequency
- Oil pressure instrument
- Water temperature instrument
- Fuel level instrument
- Engine RPM
- Number of total starting attempts
- Percentage of successful starting attempts
- Total hours of use
- Partial hours of use
- Hours left to maintenance
- Internal hour counter (not resettable) to find real hours of use
|
LIST OF ALARMS
- Engine temperature warning
- (Analogue sensor)
- High engine temperature (Analogue sensor)
- Temperature analogue sensor fault
- High engine temperature (digital sensor)
- Oil pressure warning (analogue
sensor)
- Low oil pressure (analogue
sensor)
- Pressure analogue sensor fault
- Low oil pressure (digital sensor)
- Pressure digital sensor fault
- Fuel level warning (analogue sensor)
- Low fuel level (analogue sensor)
- Level analogue sensor fault
- Low fuel level (digital sensor)
- High battery voltage
- Low battery voltage
- Inefficient battery
- Battery charger alternator failure
- ”W” signal failure
- Low engine rpm
- High engine rpm
- Starting failure
- Emergency stop
- Unexpected stop
- Engine stop failure
- Low generator frequency
- High generator frequency
- Low generator voltage
- High generator voltage
- Generator asymmetry
- Generator short-circuit
- Generator overload
- External generator protection
- Switch tripped
- Incorrect generator phase sequence
- Incorrect mains phase sequence
- Wrong system frequency setting
- Generator contactor failure
- Mains contactor failure
- Maintenance request in a number of steps
- System error
- Fuel transfer empty
- Fuel transfer too full
- Rent hours exausted
- Low radiator liquid level
|
VARIOUS FUNCTIONS
- 1 RS232 port for: SETUP board, Remote Control, Connection to traditional modem,
GSM modem, GPS system, communication protocol MODBUS, communication by LAN/ETHERNET.
- Standard EJP function (for the French
market)
- EJP/T function (for the French market)
- SCR function (generator start and
- switchover also in the presence of voltage by an external signal)
- Gas engine function
- Decelerated starting and stopping function
- Sparkplugs pre-heating function
- Keyboard lockout function
- Generator start function according to the users kW
- Fuel topping up pump control function by 4 levels sensor
- Rental function that can be set by hours
- Dummy load control function
- Restore function by issuing a programmable relay of the state of the
card operating mode (e.g. reset or cycle state, etc.)
- Possibility to lock all the functions at a given number of working, maintenance or
rental hours
- Daily, weekly or monthly automatic test External Start
- External Stop
- 8 programmable user’s alarm
- 3 different global alarm with indipendent programmation
Main technical characteristics
- Operating temperature -20 +60°C
- Storage temperature -30+80°C
- Power supply from 9-to 33Vdc
- Voltage input measuring range 50/620Vac
- Frequency range 45 - 65Hz
- Front panel protection rating IP64
- Measuring precision ±1% - ±1 digit
- Type of measurement :True effective value (RMS)
|
